Upload files to 'tmp'

tmp/bh1750fvi.py

@@ -0,0 +1,40 @@
+#   Copyright 2016 Peter Dahlberg
+#
+#   Licensed under the Apache License, Version 2.0 (the "License");
+#   you may not use this file except in compliance with the License.
+#   You may obtain a copy of the License at
+#
+#       http://www.apache.org/licenses/LICENSE-2.0
+#
+#   Unless required by applicable law or agreed to in writing, software
+#   distributed under the License is distributed on an "AS IS" BASIS,
+#   WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+#   See the License for the specific language governing permissions and
+#   limitations under the License.
+
+import time
+
+OP_SINGLE_HRES1 = 0x20
+OP_SINGLE_HRES2 = 0x21
+OP_SINGLE_LRES = 0x23
+
+DELAY_HMODE = 180  # 180ms in H-mode
+DELAY_LMODE = 24  # 24ms in L-mode
+
+
+def sample(i2c, mode=OP_SINGLE_HRES1, i2c_addr=0x23):
+    """
+        Performs a single sampling. returns the result in lux
+    """
+
+    i2c.writeto(i2c_addr, b"\x00")  # make sure device is in a clean state
+    i2c.writeto(i2c_addr, b"\x01")  # power up
+    i2c.writeto(i2c_addr, bytes([mode]))  # set measurement mode
+
+    time.sleep_ms(DELAY_LMODE if mode == OP_SINGLE_LRES else DELAY_HMODE)
+
+    raw = i2c.readfrom(i2c_addr, 2)
+    i2c.writeto(i2c_addr, b"\x00")  # power down again
+
+    # we must divide the end result by 1.2 to get the lux
+    return ((raw[0] << 24) | (raw[1] << 16)) // 78642

tmp/bmp280.py

@@ -0,0 +1,322 @@
+from micropython import const
+from ustruct import unpack as unp
+
+# Author David Stenwall Wahlund (david at dafnet.se)
+
+# Power Modes
+BMP280_POWER_SLEEP = const(0)
+BMP280_POWER_FORCED = const(1)
+BMP280_POWER_NORMAL = const(3)
+
+BMP280_SPI3W_ON = const(1)
+BMP280_SPI3W_OFF = const(0)
+
+BMP280_TEMP_OS_SKIP = const(0)
+BMP280_TEMP_OS_1 = const(1)
+BMP280_TEMP_OS_2 = const(2)
+BMP280_TEMP_OS_4 = const(3)
+BMP280_TEMP_OS_8 = const(4)
+BMP280_TEMP_OS_16 = const(5)
+
+BMP280_PRES_OS_SKIP = const(0)
+BMP280_PRES_OS_1 = const(1)
+BMP280_PRES_OS_2 = const(2)
+BMP280_PRES_OS_4 = const(3)
+BMP280_PRES_OS_8 = const(4)
+BMP280_PRES_OS_16 = const(5)
+
+# Standby settings in ms
+BMP280_STANDBY_0_5 = const(0)
+BMP280_STANDBY_62_5 = const(1)
+BMP280_STANDBY_125 = const(2)
+BMP280_STANDBY_250 = const(3)
+BMP280_STANDBY_500 = const(4)
+BMP280_STANDBY_1000 = const(5)
+BMP280_STANDBY_2000 = const(6)
+BMP280_STANDBY_4000 = const(7)
+
+# IIR Filter setting
+BMP280_IIR_FILTER_OFF = const(0)
+BMP280_IIR_FILTER_2 = const(1)
+BMP280_IIR_FILTER_4 = const(2)
+BMP280_IIR_FILTER_8 = const(3)
+BMP280_IIR_FILTER_16 = const(4)
+
+# Oversampling setting
+BMP280_OS_ULTRALOW = const(0)
+BMP280_OS_LOW = const(1)
+BMP280_OS_STANDARD = const(2)
+BMP280_OS_HIGH = const(3)
+BMP280_OS_ULTRAHIGH = const(4)
+
+# Oversampling matrix
+# (PRESS_OS, TEMP_OS, sample time in ms)
+_BMP280_OS_MATRIX = [
+    [BMP280_PRES_OS_1, BMP280_TEMP_OS_1, 7],
+    [BMP280_PRES_OS_2, BMP280_TEMP_OS_1, 9],
+    [BMP280_PRES_OS_4, BMP280_TEMP_OS_1, 14],
+    [BMP280_PRES_OS_8, BMP280_TEMP_OS_1, 23],
+    [BMP280_PRES_OS_16, BMP280_TEMP_OS_2, 44]
+]
+
+# Use cases
+BMP280_CASE_HANDHELD_LOW = const(0)
+BMP280_CASE_HANDHELD_DYN = const(1)
+BMP280_CASE_WEATHER = const(2)
+BMP280_CASE_FLOOR = const(3)
+BMP280_CASE_DROP = const(4)
+BMP280_CASE_INDOOR = const(5)
+
+_BMP280_CASE_MATRIX = [
+    [BMP280_POWER_NORMAL, BMP280_OS_ULTRAHIGH, BMP280_IIR_FILTER_4, BMP280_STANDBY_62_5],
+    [BMP280_POWER_NORMAL, BMP280_OS_STANDARD, BMP280_IIR_FILTER_16, BMP280_STANDBY_0_5],
+    [BMP280_POWER_FORCED, BMP280_OS_ULTRALOW, BMP280_IIR_FILTER_OFF, BMP280_STANDBY_0_5],
+    [BMP280_POWER_NORMAL, BMP280_OS_STANDARD, BMP280_IIR_FILTER_4, BMP280_STANDBY_125],
+    [BMP280_POWER_NORMAL, BMP280_OS_LOW, BMP280_IIR_FILTER_OFF, BMP280_STANDBY_0_5],
+    [BMP280_POWER_NORMAL, BMP280_OS_ULTRAHIGH, BMP280_IIR_FILTER_16, BMP280_STANDBY_0_5]
+]
+
+_BMP280_REGISTER_ID = const(0xD0)
+_BMP280_REGISTER_RESET = const(0xE0)
+_BMP280_REGISTER_STATUS = const(0xF3)
+_BMP280_REGISTER_CONTROL = const(0xF4)
+_BMP280_REGISTER_CONFIG = const(0xF5)  # IIR filter config
+
+_BMP280_REGISTER_DATA = const(0xF7)
+
+
+class BMP280:
+    def __init__(self, i2c_bus, addr=0x76, use_case=BMP280_CASE_HANDHELD_DYN):
+        self._bmp_i2c = i2c_bus
+        self._i2c_addr = addr
+
+        # read calibration data
+        # < little-endian
+        # H unsigned short
+        # h signed short
+        self._T1 = unp('<H', self._read(0x88, 2))[0]
+        self._T2 = unp('<h', self._read(0x8A, 2))[0]
+        self._T3 = unp('<h', self._read(0x8C, 2))[0]
+        self._P1 = unp('<H', self._read(0x8E, 2))[0]
+        self._P2 = unp('<h', self._read(0x90, 2))[0]
+        self._P3 = unp('<h', self._read(0x92, 2))[0]
+        self._P4 = unp('<h', self._read(0x94, 2))[0]
+        self._P5 = unp('<h', self._read(0x96, 2))[0]
+        self._P6 = unp('<h', self._read(0x98, 2))[0]
+        self._P7 = unp('<h', self._read(0x9A, 2))[0]
+        self._P8 = unp('<h', self._read(0x9C, 2))[0]
+        self._P9 = unp('<h', self._read(0x9E, 2))[0]
+
+        # output raw
+        self._t_raw = 0
+        self._t_fine = 0
+        self._t = 0
+
+        self._p_raw = 0
+        self._p = 0
+
+        self.read_wait_ms = 0  # interval between forced measure and readout
+        self._new_read_ms = 200  # interval between
+        self._last_read_ts = 0
+
+        if use_case is not None:
+            self.use_case(use_case)
+
+    def _read(self, addr, size=1):
+        return self._bmp_i2c.readfrom_mem(self._i2c_addr, addr, size)
+
+    def _write(self, addr, b_arr):
+        if not type(b_arr) is bytearray:
+            b_arr = bytearray([b_arr])
+        return self._bmp_i2c.writeto_mem(self._i2c_addr, addr, b_arr)
+
+    def _gauge(self):
+        # TODO limit new reads
+        # read all data at once (as by spec)
+        d = self._read(_BMP280_REGISTER_DATA, 6)
+
+        self._p_raw = (d[0] << 12) + (d[1] << 4) + (d[2] >> 4)
+        self._t_raw = (d[3] << 12) + (d[4] << 4) + (d[5] >> 4)
+
+        self._t_fine = 0
+        self._t = 0
+        self._p = 0
+
+    def reset(self):
+        self._write(_BMP280_REGISTER_RESET, 0xB6)
+
+    def load_test_calibration(self):
+        self._T1 = 27504
+        self._T2 = 26435
+        self._T3 = -1000
+        self._P1 = 36477
+        self._P2 = -10685
+        self._P3 = 3024
+        self._P4 = 2855
+        self._P5 = 140
+        self._P6 = -7
+        self._P7 = 15500
+        self._P8 = -14600
+        self._P9 = 6000
+
+    def load_test_data(self):
+        self._t_raw = 519888
+        self._p_raw = 415148
+
+    def print_calibration(self):
+        print("T1: {} {}".format(self._T1, type(self._T1)))
+        print("T2: {} {}".format(self._T2, type(self._T2)))
+        print("T3: {} {}".format(self._T3, type(self._T3)))
+        print("P1: {} {}".format(self._P1, type(self._P1)))
+        print("P2: {} {}".format(self._P2, type(self._P2)))
+        print("P3: {} {}".format(self._P3, type(self._P3)))
+        print("P4: {} {}".format(self._P4, type(self._P4)))
+        print("P5: {} {}".format(self._P5, type(self._P5)))
+        print("P6: {} {}".format(self._P6, type(self._P6)))
+        print("P7: {} {}".format(self._P7, type(self._P7)))
+        print("P8: {} {}".format(self._P8, type(self._P8)))
+        print("P9: {} {}".format(self._P9, type(self._P9)))
+
+    def _calc_t_fine(self):
+        # From datasheet page 22
+        self._gauge()
+        if self._t_fine == 0:
+            var1 = (((self._t_raw >> 3) - (self._T1 << 1)) * self._T2) >> 11
+            var2 = (((((self._t_raw >> 4) - self._T1)
+                      * ((self._t_raw >> 4)
+                         - self._T1)) >> 12)
+                    * self._T3) >> 14
+            self._t_fine = var1 + var2
+
+    @property
+    def temperature(self):
+        self._calc_t_fine()
+        if self._t == 0:
+            self._t = ((self._t_fine * 5 + 128) >> 8) / 100.
+        return self._t
+
+    @property
+    def pressure(self):
+        # From datasheet page 22
+        self._calc_t_fine()
+        if self._p == 0:
+            var1 = self._t_fine - 128000
+            var2 = var1 * var1 * self._P6
+            var2 = var2 + ((var1 * self._P5) << 17)
+            var2 = var2 + (self._P4 << 35)
+            var1 = ((var1 * var1 * self._P3) >> 8) + ((var1 * self._P2) << 12)
+            var1 = (((1 << 47) + var1) * self._P1) >> 33
+
+            if var1 == 0:
+                return 0
+
+            p = 1048576 - self._p_raw
+            p = int((((p << 31) - var2) * 3125) / var1)
+            var1 = (self._P9 * (p >> 13) * (p >> 13)) >> 25
+            var2 = (self._P8 * p) >> 19
+
+            p = ((p + var1 + var2) >> 8) + (self._P7 << 4)
+            self._p = p / 256.0
+        return self._p
+
+    def _write_bits(self, address, value, length, shift=0):
+        d = self._read(address)[0]
+        m = int('1' * length, 2) << shift
+        d &= ~m
+        d |= m & value << shift
+        self._write(address, d)
+
+    def _read_bits(self, address, length, shift=0):
+        d = self._read(address)[0]
+        return d >> shift & int('1' * length, 2)
+
+    @property
+    def standby(self):
+        return self._read_bits(_BMP280_REGISTER_CONFIG, 3, 5)
+
+    @standby.setter
+    def standby(self, v):
+        assert 0 <= v <= 7
+        self._write_bits(_BMP280_REGISTER_CONFIG, v, 3, 5)
+
+    @property
+    def iir(self):
+        return self._read_bits(_BMP280_REGISTER_CONFIG, 3, 2)
+
+    @iir.setter
+    def iir(self, v):
+        assert 0 <= v <= 4
+        self._write_bits(_BMP280_REGISTER_CONFIG, v, 3, 2)
+
+    @property
+    def spi3w(self):
+        return self._read_bits(_BMP280_REGISTER_CONFIG, 1)
+
+    @spi3w.setter
+    def spi3w(self, v):
+        assert v in (0, 1)
+        self._write_bits(_BMP280_REGISTER_CONFIG, v, 1)
+
+    @property
+    def temp_os(self):
+        return self._read_bits(_BMP280_REGISTER_CONTROL, 3, 5)
+
+    @temp_os.setter
+    def temp_os(self, v):
+        assert 0 <= v <= 5
+        self._write_bits(_BMP280_REGISTER_CONTROL, v, 3, 5)
+
+    @property
+    def press_os(self):
+        return self._read_bits(_BMP280_REGISTER_CONTROL, 3, 2)
+
+    @press_os.setter
+    def press_os(self, v):
+        assert 0 <= v <= 5
+        self._write_bits(_BMP280_REGISTER_CONTROL, v, 3, 2)
+
+    @property
+    def power_mode(self):
+        return self._read_bits(_BMP280_REGISTER_CONTROL, 2)
+
+    @power_mode.setter
+    def power_mode(self, v):
+        assert 0 <= v <= 3
+        self._write_bits(_BMP280_REGISTER_CONTROL, v, 2)
+
+    @property
+    def is_measuring(self):
+        return bool(self._read_bits(_BMP280_REGISTER_STATUS, 1, 3))
+
+    @property
+    def is_updating(self):
+        return bool(self._read_bits(_BMP280_REGISTER_STATUS, 1))
+
+    @property
+    def chip_id(self):
+        return self._read(_BMP280_REGISTER_ID, 2)
+
+    @property
+    def in_normal_mode(self):
+        return self.power_mode == BMP280_POWER_NORMAL
+
+    def force_measure(self):
+        self.power_mode = BMP280_POWER_FORCED
+
+    def normal_measure(self):
+        self.power_mode = BMP280_POWER_NORMAL
+
+    def sleep(self):
+        self.power_mode = BMP280_POWER_SLEEP
+
+    def use_case(self, uc):
+        assert 0 <= uc <= 5
+        pm, oss, iir, sb = _BMP280_CASE_MATRIX[uc]
+        t_os, p_os, self.read_wait_ms = _BMP280_OS_MATRIX[oss]
+        self._write(_BMP280_REGISTER_CONFIG, (iir << 2) + (sb << 5))
+        self._write(_BMP280_REGISTER_CONTROL, pm + (p_os << 2) + (t_os << 5))
+
+    def oversample(self, oss):
+        assert 0 <= oss <= 4
+        t_os, p_os, self.read_wait_ms = _BMP280_OS_MATRIX[oss]
+        self._write_bits(_BMP280_REGISTER_CONTROL, p_os + (t_os << 3), 2)

tmp/boot.py

@@ -0,0 +1,5 @@
+# This file is executed on every boot (including wake-boot from deepsleep)
+#import esp
+#esp.osdebug(None)
+#import webrepl
+#webrepl.start()

tmp/lcdtest.py

@@ -0,0 +1,22 @@
+from machine import Pin, SoftI2C
+import ssd1306
+from time import sleep
+
+pin16 = Pin(16, Pin.OUT)
+pin16.value(1)
+
+# ESP32 Pin assignment 
+i2c = SoftI2C(scl=Pin(15), sda=Pin(4))
+
+# ESP8266 Pin assignment
+#i2c = SoftI2C(scl=Pin(5), sda=Pin(4))
+
+oled_width = 128
+oled_height = 64
+oled = ssd1306.SSD1306_I2C(oled_width, oled_height, i2c)
+
+oled.text('Hello, World 1!', 0, 0)
+oled.text('Hello, World 2!', 0, 15)
+oled.text('Hello, World 3!', 0, 25)
+        
+oled.show()

tmp/lux22ttt.py

@@ -0,0 +1,8 @@
+import bh1750fvi
+from machine import I2C,Pin
+
+scl = Pin(22)
+sda = Pin(21)
+i2c = I2C(scl=scl, sda=sda)
+result = bh1750fvi.sample(i2c) # in lux
+print(result)